Leading 10 typical forklift crashes ， forklift operation must pay attention to these matters ！.
Leading 10 typical forklift crashes ， forklift operation must pay attention to these matters ！.
Blog Article
Don't underestimate the forklift at the workplace. If the procedure is not good, there will be major mishaps in mins, and there are lots of accidents involving forklifts.
Situation 1: The forklift cargo blocked the motorist's view, and the person in front might not be discovered, leading to a rolling accident.
Case 2: In order to maintain the balance of the forklift when raising hefty items, the workers used their body weight as the counterweight, which practically triggered casualties.
Case 3: The width of the forklift freight goes beyond the allowed width of the route and holds on the roadside rack, which nearly triggers an accident.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift driver did not see the pedestrian, and the pedestrian did not see the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift motorist does not use the seat belt, the forklift lifter drops and the motorist is crushed when the forklift rolls over.
Instance 7: The forklift motorist did not wear a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift operation must focus on these matters ：.
Beginning.
1. Prior to starting, observe the environments, and after confirming that there are no barriers that impede the safety of driving, beep the horn first and afterwards start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge have to be risk-free prior to starting.
3. When the forklift begins with a load, the vehicle driver ought to initially confirm that the lots is stable and trusted.
4. The begin has to be sluggish and stable.
Driving.
1. When driving, the height between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole needs to be tilted in reverse. .
2. Do not lift the fork too expensive when driving. When getting in and leaving the job website or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork needs to not be raised too expensive, which will certainly influence the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the normal driving setting prior to driving. .
4. When transforming, if there are pedestrians or vehicles nearby, the driving signal must be provided initially. High-speed doglegs are restricted. High-speed sharp turns will certainly create the vehicle to lose lateral stability and tip over. .
5. When the forklift is downhill, it is purely restricted to switch off the fire and slide, and it is forbidden to brake all of a sudden while driving with tons unless there are unique conditions.
6. When the forklift is running, it must obey the website traffic rules in the factory and need to keep a particular security distance from the vehicle in front. .
7. When the forklift is running, the load must be in the lowest setting that does not impede the driving, and the gantry needs to be effectively tilted back. The load shall not be elevated other than when piling or filling. .
8. The height of the tons need to not block the motorist's sight. In unique circumstances, when the item influences the forward vision, drive at a low rate when turning around.
9. It is restricted to switch on the ramp, neither to drive throughout the ramp. .
10. The secure driving speed of the forklift in the manufacturing facility area is 5 km/h, and it has to drive safely at a reduced rate when entering the manufacturing workshop area. .
11. When the forklift is raised, raised or driven, it is restricted for workers to stand on the fork to hold items and play a stabilizing function. .
12. If troubles are found, they will be repaired and reported in a prompt way, and they will certainly never operate with diseases or conceal them.
loading and dumping.
1. When fork-loading things, the distance in between the two forks must be readjusted as required to make the load of both forks balanced and not skewed, and one side Stand-on Electric Pallet Stacker of the item should be against the rack. .
2. It is forbidden to work with a solitary fork or make use of a fork top or pull. In unique situations, safety indication must be established to remind bordering pedestrians. .
3. In the process of packing and unloading items, the forklift must be stopped with the brake. .
4. The rate of the lorry should be slow and constant. Beware not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm individuals. .
5. When using a fork to fork the goods, the fork should be as deep as possible under the tons, and it should be noted that the fork pointer ought to not touch other goods or items. The lots needs to be supported with marginal back tilt of the gantry so that the load does not slide backwards. The mast can be slanted onward a little when the tons is reduced to enable easy positioning of the lots and removal of the forks. .
6. It is forbidden to fork products at broadband and hit tough items with the fork head. .
7. When the forklift is functioning, it is prohibited for people to loaf the fork, so regarding stay clear of the collapse of the goods and harm people. .
8. Overloading is prohibited, and Stand-on Electric Pallet Stacker it is prohibited to use forks to raise employees to participate in high-altitude operations to avoid high-altitude dropping mishaps. .
9. It is not enabled to utilize the brake inertia to slip, place, round or roll items. .
10. It is not enabled to use forks to select, transform pallet unload.
Leaving .
1. It is forbidden to leave the forklift when the things on the fork are in the air. Before leaving the forklift, you have to unload the goods or lower the fork structure.
2. Draw the parking brake deal with to dead or depress the hand brake switch.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 min).
4. Get rid of the secret. .
Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance should be examined, and gas, lubing oil and cooling water ought to be added.
2. Examine the safety and security efficiency of starting, running and braking.
3. Examine whether the lights and horn signals are full and efficient.
4. During the operation of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the exterior leak ought to also be checked and the seals need to be changed in time.
Forklift Safety Operation Specifications.
1. You have to inspect before leaving the vehicle;.
2. When you encounter a person before you during driving, you need to send a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the nadir of the freight should be 0.3 m ~ 0.4 m in the air;.
5. The turning should not be as well sharp to prevent the propensity of " complimentary turning";.
6. Adding and down the slope must be sluggish and uniform, and no turning on the slope is allowed.
7. Do not drive across the slope. When the gradient is greater than 10%, the lorry needs to be driven in reverse when going downhill;.
8. When the forklift workers bring the goods and progress, if they experience large or heavy items and go to the chauffeur's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" need to be adhered to in the procedure.
1. Solitary fork procedure is not enabled.
2. It is not permitted to lift the goods for far away driving.
3. It is not enabled to get the goods by turning over the pallet with the fork.
4. It is not enabled to directly shovel chemicals, flammables and various other unsafe chemicals with forks.
5. It is not permitted to utilize inertia pressure to pick up the goods.
6. It is not permitted to use braking pressure to expatriation round or easy-to-roll objects.
7. It is not allowed to bring individuals to work on the pallet or fork, and it is strictly forbidden to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Parking is not allowed under the following problems.
1. Curves, narrow roads, railway crossings;.
2. Areas with a longitudinal slope greater than 5%.
3. When there is an obstacle on one side of the roadway, the opposite side of the area with the very same size as the obstacle should be within 20 meters at each end.
Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844